https://stratum0.org/mediawiki/index.php?action=history&feed=atom&title=RepRap%2FConfigs%2FSlic3r%2FKasalehlia%2Fsolid.ini 2026-04-21T16:16:44Z Versionsgeschichte dieser Seite in Stratum 0 MediaWiki 1.31.2 https://stratum0.org/mediawiki/index.php?title=RepRap/Configs/Slic3r/Kasalehlia/solid.ini&diff=8778&oldid=prev 2014-10-12T21:41:13Z

<p>ausgelagert aus <a href="/wiki/RepRap/Configs/Slic3r" class="mw-redirect" title="RepRap/Configs/Slic3r">RepRap/Configs/Slic3r</a></p> <p><b>Neue Seite</b></p><div>avoid_crossing_perimeters = 0<br /> bottom_solid_layers = 3<br /> bridge_acceleration = 0<br /> bridge_flow_ratio = 1<br /> bridge_speed = 60<br /> brim_width = 3<br /> complete_objects = 0<br /> default_acceleration = 0<br /> external_perimeter_speed = 70%<br /> external_perimeters_first = 0<br /> extra_perimeters = 1<br /> extruder_clearance_height = 20<br /> extruder_clearance_radius = 20<br /> extrusion_width = 0<br /> fill_angle = 45<br /> fill_density = 0.3<br /> fill_pattern = honeycomb<br /> first_layer_acceleration = 0<br /> first_layer_extrusion_width = 200%<br /> first_layer_height = 0.22<br /> first_layer_speed = 30%<br /> gap_fill_speed = 20<br /> gcode_comments = 0<br /> infill_acceleration = 0<br /> infill_every_layers = 1<br /> infill_extruder = 1<br /> infill_extrusion_width = 0<br /> infill_first = 0<br /> infill_only_where_needed = 0<br /> infill_speed = 60<br /> layer_height = 0.22<br /> min_skirt_length = 0<br /> notes = <br /> only_retract_when_crossing_perimeters = 1<br /> ooze_prevention = 0<br /> output_filename_format = [input_filename_base].gcode<br /> overhangs = 1<br /> perimeter_acceleration = 0<br /> perimeter_extruder = 1<br /> perimeter_extrusion_width = 0<br /> perimeter_speed = 50<br /> perimeters = 3<br /> post_process = <br /> raft_layers = 0<br /> randomize_start = 0<br /> resolution = 0<br /> skirt_distance = 6<br /> skirt_height = 1<br /> skirts = 2<br /> small_perimeter_speed = 40<br /> solid_fill_pattern = concentric<br /> solid_infill_below_area = 70<br /> solid_infill_every_layers = 0<br /> solid_infill_extrusion_width = 0<br /> solid_infill_speed = 60<br /> spiral_vase = 0<br /> standby_temperature_delta = -5<br /> start_perimeters_at_concave_points = 0<br /> start_perimeters_at_non_overhang = 0<br /> support_material = 0<br /> support_material_angle = 0<br /> support_material_enforce_layers = 0<br /> support_material_extruder = 1<br /> support_material_extrusion_width = 0<br /> support_material_interface_extruder = 1<br /> support_material_interface_layers = 0<br /> support_material_interface_spacing = 0<br /> support_material_pattern = rectilinear<br /> support_material_spacing = 2.5<br /> support_material_speed = 60<br /> support_material_threshold = 0<br /> thin_walls = 1<br /> threads = 2<br /> top_infill_extrusion_width = 0<br /> top_solid_infill_speed = 50<br /> top_solid_layers = 5<br /> travel_speed = 130</div>

Daniel Bohrer