https://stratum0.org/mediawiki/index.php?action=history&feed=atom&title=RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_gross.ini 2026-04-21T16:16:17Z Versionsgeschichte dieser Seite in Stratum 0 MediaWiki 1.31.2 https://stratum0.org/mediawiki/index.php?title=RepRap/Configs/Slic3r/Sintox/abs_gross.ini&diff=10485&oldid=prev 2015-03-08T19:58:44Z

<p>Die Seite wurde neu angelegt: „avoid_crossing_perimeters = 0 bed_shape = 0x0,200x0,200x200,0x200 bed_temperature = 80 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_fan_speed = 100 b…“</p> <p><b>Neue Seite</b></p><div>avoid_crossing_perimeters = 0<br /> bed_shape = 0x0,200x0,200x200,0x200<br /> bed_temperature = 80<br /> bottom_solid_layers = 3<br /> bridge_acceleration = 0<br /> bridge_fan_speed = 100<br /> bridge_flow_ratio = 1<br /> bridge_speed = 60<br /> brim_width = 0<br /> complete_objects = 0<br /> cooling = 1<br /> default_acceleration = 0<br /> disable_fan_first_layers = 1<br /> dont_support_bridges = 1<br /> duplicate_distance = 6<br /> end_gcode = M84 ; disable motors\nM104 S0 ; turn off extruder temperature\nG0 X0 ; move X axis to 0\nG1 Y198 F6000 ; drive print table all the way out\nM84 ; disable motors\n<br /> external_perimeter_extrusion_width = 0<br /> external_perimeter_speed = 70%<br /> external_perimeters_first = 0<br /> extra_perimeters = 1<br /> extruder_clearance_height = 20<br /> extruder_clearance_radius = 20<br /> extruder_offset = 0x0<br /> extrusion_axis = E<br /> extrusion_multiplier = 1<br /> extrusion_width = 0<br /> fan_always_on = 1<br /> fan_below_layer_time = 60<br /> filament_diameter = 1.75<br /> fill_angle = 45<br /> fill_density = 35%<br /> fill_pattern = honeycomb<br /> first_layer_acceleration = 0<br /> first_layer_bed_temperature = 80<br /> first_layer_extrusion_width = 200%<br /> first_layer_height = 0.25<br /> first_layer_speed = 50%<br /> first_layer_temperature = 240<br /> gap_fill_speed = 20<br /> gcode_arcs = 0<br /> gcode_comments = 0<br /> gcode_flavor = reprap<br /> infill_acceleration = 0<br /> infill_every_layers = 1<br /> infill_extruder = 1<br /> infill_extrusion_width = 0<br /> infill_first = 0<br /> infill_only_where_needed = 0<br /> infill_speed = 70<br /> interface_shells = 0<br /> layer_gcode = <br /> layer_height = 0.2<br /> max_fan_speed = 100<br /> min_fan_speed = 35<br /> min_print_speed = 10<br /> min_skirt_length = 0<br /> notes = <br /> nozzle_diameter = 0.5<br /> only_retract_when_crossing_perimeters = 1<br /> ooze_prevention = 0<br /> output_filename_format = [input_filename_base].gcode<br /> overhangs = 1<br /> perimeter_acceleration = 0<br /> perimeter_extruder = 1<br /> perimeter_extrusion_width = 0<br /> perimeter_speed = 80<br /> perimeters = 3<br /> post_process = <br /> raft_layers = 0<br /> resolution = 0<br /> retract_before_travel = 2<br /> retract_layer_change = 1<br /> retract_length = 5<br /> retract_length_toolchange = 10<br /> retract_lift = 1<br /> retract_restart_extra = 0<br /> retract_restart_extra_toolchange = 0<br /> retract_speed = 40<br /> seam_position = aligned<br /> skirt_distance = 2<br /> skirt_height = 1<br /> skirts = 1<br /> slowdown_below_layer_time = 30<br /> small_perimeter_speed = 30<br /> solid_fill_pattern = rectilinear<br /> solid_infill_below_area = 70<br /> solid_infill_every_layers = 0<br /> solid_infill_extrusion_width = 0<br /> solid_infill_speed = 70<br /> spiral_vase = 0<br /> standby_temperature_delta = -5<br /> start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG92 Y40; set position to Y=0\nG28 Z0; home Z<br /> support_material = 1<br /> support_material_angle = 0<br /> support_material_enforce_layers = 0<br /> support_material_extruder = 1<br /> support_material_extrusion_width = 0<br /> support_material_interface_extruder = 1<br /> support_material_interface_layers = 3<br /> support_material_interface_spacing = 0<br /> support_material_interface_speed = 100%<br /> support_material_pattern = rectilinear<br /> support_material_spacing = 2.5<br /> support_material_speed = 20<br /> support_material_threshold = 0<br /> temperature = 240<br /> thin_walls = 1<br /> threads = 2<br /> toolchange_gcode = <br /> top_infill_extrusion_width = 0<br /> top_solid_infill_speed = 60<br /> top_solid_layers = 4<br /> travel_speed = 130<br /> use_firmware_retraction = 0<br /> use_relative_e_distances = 0<br /> vibration_limit = 0<br /> wipe = 0<br /> xy_size_compensation = 0<br /> z_offset = 0</div>

Sintox