https://stratum0.org/mediawiki/index.php?action=history&feed=atom&title=RepRap%2FConfigs%2FSlic3r%2Fnetz39.ini 2026-04-21T19:12:24Z Versionsgeschichte dieser Seite in Stratum 0 MediaWiki 1.31.2 https://stratum0.org/mediawiki/index.php?title=RepRap/Configs/Slic3r/netz39.ini&diff=8782&oldid=prev 2014-10-12T21:48:25Z

<p>ausgelagert aus <a href="/wiki/RepRap/Configs/Slic3r" class="mw-redirect" title="RepRap/Configs/Slic3r">RepRap/Configs/Slic3r</a></p> <p><b>Neue Seite</b></p><div># generated by Slic3r 0.9.9-dev on Mon Jun 3 17:06:48 2013<br /> avoid_crossing_perimeters = 0<br /> bed_size = 180,200<br /> bed_temperature = 50<br /> bottom_solid_layers = 5<br /> bridge_acceleration = 0<br /> bridge_fan_speed = 100<br /> bridge_flow_ratio = 1<br /> bridge_speed = 30<br /> brim_width = 0<br /> complete_objects = 1<br /> cooling = <br /> default_acceleration = 0<br /> disable_fan_first_layers = 1<br /> duplicate = 1<br /> duplicate_distance = 6<br /> duplicate_grid = 1,1<br /> end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors<br /> external_perimeter_speed = 40%<br /> external_perimeters_first = 0<br /> extra_perimeters = <br /> extruder_clearance_height = 35<br /> extruder_clearance_radius = 62<br /> extruder_offset = 0x0<br /> extrusion_axis = E<br /> extrusion_multiplier = 1.1<br /> extrusion_width = 0<br /> fan_always_on = 0<br /> fan_below_layer_time = 60<br /> filament_diameter = 1.75<br /> fill_angle = 30<br /> fill_density = 0.5<br /> fill_pattern = rectilinear<br /> first_layer_bed_temperature = 50<br /> first_layer_extrusion_width = 0<br /> first_layer_height = 150%<br /> first_layer_speed = 40%<br /> first_layer_temperature = 197<br /> g0 = 0<br /> gap_fill_speed = 20<br /> gcode_arcs = 0<br /> gcode_comments = 0<br /> gcode_flavor = reprap<br /> infill_acceleration = 0<br /> infill_every_layers = 1<br /> infill_extruder = 1<br /> infill_extrusion_width = 0<br /> infill_first = 0<br /> infill_only_where_needed = 0<br /> infill_speed = 60<br /> layer_gcode = <br /> layer_height = 0.2<br /> max_fan_speed = 100<br /> min_fan_speed = 35<br /> min_print_speed = 5<br /> min_skirt_length = 15<br /> notes = config for printing netz39 pieces<br /> nozzle_diameter = 0.33<br /> only_retract_when_crossing_perimeters = 1<br /> output_filename_format = [input_filename_base].gcode<br /> perimeter_acceleration = 0<br /> perimeter_extruder = 1<br /> perimeter_extrusion_width = 0<br /> perimeter_speed = 60<br /> perimeters = 3<br /> post_process = <br /> print_center = 90,100<br /> raft_layers = 0<br /> randomize_start = <br /> resolution = 0<br /> retract_before_travel = 0<br /> retract_layer_change = 1<br /> retract_length = 2<br /> retract_length_toolchange = 5<br /> retract_lift = 0<br /> retract_restart_extra = 0<br /> retract_restart_extra_toolchange = 0<br /> retract_speed = 50<br /> rotate = 0<br /> scale = 1<br /> skirt_distance = 5<br /> skirt_height = 1<br /> skirts = 2<br /> slowdown_below_layer_time = 50<br /> small_perimeter_speed = 60%<br /> solid_fill_pattern = rectilinear<br /> solid_infill_below_area = 0<br /> solid_infill_every_layers = 0<br /> solid_infill_extrusion_width = 0<br /> solid_infill_speed = 100%<br /> start_gcode = G28 ; home all axes\nM92 E820<br /> support_material = <br /> support_material_angle = 45<br /> support_material_enforce_layers = 0<br /> support_material_extruder = 1<br /> support_material_extrusion_width = 0<br /> support_material_interface_layers = 0<br /> support_material_interface_spacing = 0<br /> support_material_pattern = rectilinear<br /> support_material_spacing = 2<br /> support_material_speed = 60<br /> support_material_threshold = 41<br /> temperature = 188<br /> threads = 2<br /> toolchange_gcode = <br /> top_infill_extrusion_width = 0<br /> top_solid_infill_speed = 70%<br /> top_solid_layers = 5<br /> travel_speed = 100<br /> use_relative_e_distances = 0<br /> vibration_limit = 0<br /> z_offset = 0</div>

Daniel Bohrer